Field manual

STEP vs STL: which file format to use

Use STEP when someone needs to inspect, machine or re-use the real geometry. Use STL when the next step is slicing for a 3D printer or a quick look at the shape. STEP keeps exact surfaces and assembly structure; STL keeps only a mesh of triangles, with no units, colours or part names.

Updated:

Procedure

Open. Verify. Inspect.

A short workflow that preserves the original engineering file and makes the format limits visible before you rely on the result.

  1. 1

    Ask what happens next

    If the file goes to a 3D printer or a viewer, STL is enough. If it goes to a machinist, a CAM system or another engineer, send STEP.

  2. 2

    Keep the STEP as the master

    Export the STL from the STEP when you need it. Going the other way cannot recover the surfaces, so never delete the STEP after exporting a mesh.

  3. 3

    Check the result before you send

    Open the exported file in a viewer on a second device. Confirm the shape, the part count and the overall bounds against the source.

Format check
STEPExact B-Rep, curved surfaces, assemblies, AP242 tessellated
STLBinary and ASCII triangle meshes
PlatformsiPhone, iPad and Mac
CaveatSTEP coverage varies by schema edition and exporter
STEP and STL compared
STEP (.step, .stp)STL (.stl)
GeometryExact surfaces and solids (B-Rep), or tessellatedTriangles only
Assemblies and part namesKeptNot stored
Units and colourStored in the fileNot stored
Typical useExchange between CAD, CAM and suppliers3D printing, quick shape review
Editable downstreamYes, in most CAD systemsHard: a mesh has no features
EncodingPlain text (ISO 10303-21)Binary or ASCII

What a STEP file actually contains

STEP is the common name for ISO 10303, and the .step or .stp file you receive is normally a plain text exchange structure defined by part 21 of that standard. Open one in a text editor and the first line reads ISO-10303-21. Everything after it is a list of numbered records describing points, curves, surfaces, faces and how they join.

Because the surfaces are described mathematically, a cylinder is a cylinder at any zoom level. STEP can also hold an assembly tree with part names and positions, which is why a supplier asks for STEP rather than a picture or a mesh.

Some STEP files, especially AP242 exports, carry pre-tessellated geometry instead of or alongside the exact surfaces. A good viewer handles both. If you want the full background on opening these files, our guide to opening a STEP file on iPhone or iPad covers the steps.

What an STL file contains, and what it leaves out

STL describes the outer skin of an object as triangular facets. It was first documented by 3D Systems in 1988 for stereolithography and is still the default hand-off to slicing software. The Library of Congress format notes describe it as an openly documented triangle mesh format.

That simplicity is also the limit. There is no unit, so a part exported in millimetres and read as inches is 25.4 times too large. There is no colour, no material, no part name and no way to say that two triangles belong to the same hole.

The size of an STL depends on how finely the surface was cut into triangles at export. A binary STL spends 50 bytes per triangle plus an 84 byte header, so a model with 100,000 triangles is about 5 MB and one with 2 million is about 100 MB. The curved surface in the original STEP stays the same size however closely you look.

When STEP is the right choice

Send STEP to anyone who will measure, machine, re-use or modify the part, and whenever the file is an assembly. It is also the safer archive format: it can be turned into an STL of any resolution later, while an STL cannot be turned back into clean surfaces.

Make sure the receiver can open it. Neither iOS nor macOS previews STEP, so a buyer or client without a CAD seat sees a generic icon. That is the case a lightweight viewer solves.

When STL is the right choice

Send STL for printing, for a quick look at overall shape, and for any tool that only understands triangles. Pick a tessellation fine enough that curves do not look faceted at the size you will print, and no finer: past that point you only grow the file.

If you need colour or units in a mesh, ask whether 3MF or OBJ suits the destination better. Our comparison of STL, OBJ and 3MF goes through that choice.

Opening both on Apple devices

CadRoam reads STEP and STL directly in the same app. Import the file from Files, orbit and pan, hide or isolate parts in multi-part models, and read bounds, triangle count, surface area and enclosed volume where the geometry provides them. These figures are review aids, not certified measurements.

Parsing happens on the device, so a confidential part is not uploaded to a conversion service, and imported files open with no connection. Three unique files open free; unlimited local viewing, camera AR and PDF reports need CadRoam Pro, available monthly, yearly or as a one-time lifetime purchase.

Primary sources

Questions

Before you rely on the view.

Is STEP better than STL?

For exchanging real geometry, yes: STEP keeps exact surfaces, assemblies and units. For 3D printing, STL is simpler and universally accepted. They solve different problems.

Can I convert STL back to STEP?

Not into clean editable surfaces. An STL is only triangles, so any conversion produces a faceted shell. Keep the original STEP.

Why is my STL file so large?

Size follows the number of triangles. A binary STL uses 50 bytes per triangle plus an 84 byte header, so finer tessellation of curved surfaces grows the file quickly.

Can an iPhone open both formats?

Yes. CadRoam opens STEP, STP and STL on iPhone, iPad and Mac, parsed locally on the device.